From: support@mathworks.com
Sent: Thursday, April 13, 2006 4:39 PM
To: Ross Wagner, Dr.
Subject: RE: xPC Target - Cannot build model using xPC Target 2.9 and
Watcom 11.0 compiler
Hi Ross,
I am writing in reference to your Service Request # 1-2R0Q6M regarding 'Cannot build model using xPC Target 2.9 and Watcom 11.0 compiler'.
Thank you for contacting The MathWorks. The Watcom 11.0 compiler is not supported for xPC Target 2.9. xPC Target now supports Open Watcom C/C++ Version 1.3. For full information about what is new in xPC Target, please see the online documentation at:
http://www.mathworks.com/access/helpdesk/help/toolbox/xpc/rn/f0-78982.html
The Watcom Version 1.3 compiler may be downloaded at:
http://www.softpedia.com/get/Programming/Coding-languages-Compilers/Open-Watcom.shtml
Please note The MathWorks does not publish this site and therefore cannot guarantee the accuracy of its contents. Any issues with the site should be addressed with the author of the site.
If you need further assistance regarding this issue, please reply to this email preserving the THREAD ID listed below. If you have a new technical support question, please submit a new request here:
http://www.mathworks.com/contact_TS.html.
Sincerely,
John
John Bemesderfer
Application Support Engineer
Technical Support Department
The MathWorks, Inc.
Phone: (508) 647-7000 option 5
Self-Service:
http://www.mathworks.com/support
File Exchange and Newsgroup Access:
http://www.mathworks.com/matlabcentral/
[THREAD ID:1-2R0OAH]
-----Original Message-----
Sent: 2006-04-13 02:46:28 PM
To: twsupp@mathworks.com
Subject: xPC Target - Cannot build model using xPC Target 2.9 and Watcom 11.0 compiler
Topic: xpc
Brief Subject of this Help Request: Cannot build model using xPC Target 2.9 and Watcom 11.0 compiler
Are you an approved member of The MathWorks Book or Connections Program?: neither
License#: 196315
Product Release: R2006a
Product: xPC Target
Platform: Windows
Operating System: Windows XP
/tmp/equus62217/error_screen.PNG
Does the XPCTEST function pass successfully with the current hardware configuration?: No
Version output from running xpclib: 2.9
Output of getxpcenv: xPC Target default environment
Version : 2.9
CCompiler : Watcom
CompilerPath : c:\watcom
Name : RENSHAW
TargetRAMSizeMB : Auto
MaxModelSize : 16MB
SecondaryIDE : off
HostTargetComm : TcpIp
RS232HostPort : COM1
RS232Baudrate : 115200
TcpIpTargetAddress : 132.206.111.69
TcpIpTargetPort : 22222
TcpIpSubNetMask : 255.255.255.0
TcpIpGateway : 132.206.111.1
TcpIpTargetDriver : I82559
TcpIpTargetBusType : PCI
TcpIpTargetISAMemPort : 0x300
TcpIpTargetISAIRQ : 5
TargetScope : Enabled
TargetMouse : None
xPC Target Embedded Option
EmbeddedOption : Enabled
TargetBoot : BootFloppy
Output of getxpcpci('all'): List of installed PCI devices:
Bus Slot IRQ Vendor Name Device Name Device Type VendorID DeviceID
0 0 0 ***** ***** Host Bridge 1106 3099
0 1 0 ***** ***** PCI-to-PCI Bridge 1106 B099
0 5 10 ***** ***** Audio Controller 13F6 111
0 12 5 ***** ***** Ethernet Controller 8086 1229
0 13 255 ComputerBoards PCIM-DDA06/16 AO DI DO 1307 53
0 16 5 ComputerBoards PCIM-DAS1602/16 AI AO DI DO 1307 56
0 17 0 ***** ***** ISA Bridge 1106 3147
1 0 11 ***** ***** VGA comp. Controller 1002 5046
Hardware and target computer details: Not applicable. Problem is with building.
I/O Bus Type (if applicable): PCI Host-target communication connection: TCP/IP
Exact Reproduction Steps and Code: XPCTEST fails at step #4 Build and download xPC Target application using model xpcosc...
When I try to build my model I get an error message indicating an unrecognized Watcom version. (See attached screen dump.) Yet when I check on system requirements on the Mathworks page relating to xPC Target the Product Requirements secion lists that Watcom C/C++ 11.0 is supported.
Perhaps on a related note, when I run "mex -setup" I do not see the Watcom compiler come up as an option.
Expected Behavior Versus Results: Model should compile.
Error Messages (if any): See attached screen dump.
Paste Output of ver: -------------------------------------------------------------------------------------
MATLAB Version 7.2.0.232 (R2006a)
MATLAB License Number: 196315
Operating System: Microsoft Windows XP Version 5.1 (Build 2600: Service Pack 2) Java VM Version: Java 1.5.0 with Sun Microsystems Inc. Java HotSpot(TM) Client VM mixed mode
-------------------------------------------------------------------------------------
MATLAB Version 7.2 (R2006a)
Simulink Version 6.4 (R2006a)
Control System Toolbox Version 7.0 (R2006a)
Data Acquisition Toolbox Version 2.8.1 (R2006a)
Instrument Control Toolbox Version 2.4 (R2006a)
Real-Time Windows Target Version 2.6.1 (R2006a)
Real-Time Workshop Version 6.4 (R2006a)
Signal Processing Blockset Version 6.3 (R2006a)
Signal Processing Toolbox Version 6.5 (R2006a)
Statistics Toolbox Version 5.2 (R2006a)
System Identification Toolbox Version 6.1.3 (R2006a)
xPC Target Version 2.9 (R2006a)
Solution or Bug Report IDs (comma separated):
Form Page URL: /support/contact_us/ts/help_request_1.html